
Dr Jacqueline Kovacevic, dentist · KOVIVA Dental Studio, Vienna
A fine mesh for severely weakened teeth
A glass fibre mesh consists of many thin glass fibres joined into a net-like structure. Quality lies in the detail, and this is especially true for large composite fillings.
For particularly large composite fillings, we work a fine glass fibre mesh into the build-up. Later, nothing of it can be seen.
The fibre mesh is not simply there to make the filling harder. It helps distribute stress within the composite build-up more evenly, especially in deep and strongly enclosed defects. This can reduce the load on the bond between the filling and the tooth.
What is a glass fibre mesh?
GLASS FIBRES WORKED INTO COMPOSITE
A fibre mesh consists of many thin glass fibres that are joined together and processed into a net-like structure.
During treatment, the mesh is worked into the composite build-up and completely enclosed by composite. It lies flat inside the filling and can help distribute stress more evenly there.
Why is the mesh placed in a particular layer?
LAYER BY LAYER TO A STABLE BUILD-UP
A high-quality composite filling is not simply placed in the tooth as one large block. The material is applied in several layers, each cured carefully.
In deep and large defects, stress builds up during curing. Composite shrinks slightly as it polymerises, that is, as it hardens. The more the material is confined by the cavity, the harder it can be to compensate for this stress.
The fibre mesh is therefore deliberately placed in a specific layer of the build-up. It helps distribute the stress that arises and reduce the load on the bond between tooth and composite.
The mesh is then completely enclosed in composite. In the end, nothing of it is visible.
What does the C-factor have to do with it?
WHEN MANY SURFACES ARE BONDED AND ONLY A FEW ARE FREE
The so-called C-factor describes the ratio between bonded and free surfaces of a composite filling.
In a deep cavity, many surfaces of the composite are bonded to the tooth, while only a comparatively small surface is free. As a result, polymerisation shrinkage cannot simply be compensated for across a free surface. Stress can develop within the filling and at the bond.
The fibre mesh does not actually reduce the C-factor. But it can help to control the effects of this stress and distribute it within the build-up.
When can a fibre mesh make sense?
LARGE DEFECTS, THIN WALLS AND WEAKENED TEETH
A fibre mesh can be useful above all for larger composite build-ups in the back teeth. For example with large defects, very thin tooth walls, major loss of tooth structure or in selected root-treated teeth.
Root-treated teeth have often lost a particularly large amount of tooth structure. That is why it is important to make the best possible use of the remaining tooth structure and to control the load within the build-up.
For smaller defects, a composite can be used that already contains short glass fibres distributed within the material. These fibres are not joined into a mesh and do not have to be placed in the tooth separately.
For larger and deeper build-ups, a continuous fibre mesh can additionally be worked into the composite.
Which option makes sense depends on the size and position of the defect, the remaining tooth structure, the load on the tooth and the individual bite.
What are the limits?
A FIBRE MESH IS NO SUBSTITUTE FOR CAREFUL TREATMENT PLANNING
A fibre mesh is not suitable for every tooth. If a tooth is very severely weakened, an overlay or another indirect restoration may be the better solution.
Technique also plays a decisive role. The tooth must stay absolutely dry during treatment. That is why we work under a rubber dam for restorations like these.
Equally important are a careful bonding technique, correct positioning of the mesh and a layered build-up without time pressure.
In addition, the bite and possible grinding loads have to be taken into account.
Which restoration suits a tooth can therefore only be assessed after an examination and, if necessary, X-ray diagnostics.
Conclusion
A fibre mesh is worked into the build-up of selected large composite fillings. Its purpose is not simply to make the filling harder.
Rather, it can help distribute stress within the composite build-up, control the effects of polymerisation shrinkage and reduce the load on the bond to the tooth.
For smaller defects, composites with short fibres distributed in the material can be used. For larger and deeper build-ups, a continuous fibre mesh can make sense.
It is a small detail that can play an important role within a carefully planned filling built up layer by layer.
If a large filling, an extensive tooth build-up or a crown is on the table for you, we are happy to discuss whether a more tooth-preserving restoration with an integrated fibre mesh is possible and sensible. Book an initial consultation at our Dental Studio on Opernring in Vienna.
This article does not replace a dental examination. Medically reviewed by Dr Jacqueline Kovacevic.



